Ayr · Ayrshire
Bespoke Mirrors in Ayr
Mirrors with black edges in Ayr cannot be restored, but we can measure and replace them with new mirror bonded using a compatible adhesive to protect the silver.
- KA7
- KA8
- KA9
- Guide from £205
Made to measure mirrors for homes and businesses in Ayr
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
What you get
- Survey, measuring or templating of the wall or recess
- Fixing with mirror-compatible adhesive, clips or channels
- Safety backing film where the position calls for it
- Final clean and advice on protecting the edges
Working in Ayr
- Postcodes covered
- KA7, KA8, KA9 and the surrounding area, including Prestwick, Troon and Irvine
- Coast
- Ayr is about 2 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Ayr the midwinter sun reaches about 11° above the horizon at noon, with roughly 6.8 hours of daylight, rising to about 58° and 17.2 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in Scotland
- Section 4 (Safety) of the Scottish Technical Handbooks covers glazing that people could collide with, such as glass in and beside doors and low-level glazing, where safety glass is needed.
Guide prices in Ayr
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Specification choices
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bespoke Mirrors in Ayr: questions
What affects the cost of a bespoke mirror?
The main cost drivers are the size and thickness of the mirror, the number of panels, the edge finish, any tint or low-iron glass, safety backing, cut-outs and the fixing method. Very large single sheets, access through narrow stairs and full mirror walls also affect the price. See the guide prices for typical ranges.
What edge finishes can I choose for a bespoke mirror?
The main choices are a flat polished edge, a bevelled edge and an arrised edge. Polished edges give a clean, frameless look and suit mirror walls, bevels add an angled border that catches the light, and arrised edges simply take off the sharpness where a frame or channel will hide them. Bevel width can usually be chosen too.
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
Do you cover Ayr for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Ayr and the surrounding Ayrshire area, including postcode districts KA7, KA8 and KA9, and nearby Prestwick, Troon and Irvine. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Ayr
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.