Carrickfergus · County Antrim
Bespoke Mirrors in Carrickfergus
Do your sliding wardrobe doors in Carrickfergus need new mirror panels? We can measure, cut and fit safety-backed mirror to suit the existing door frames.
- BT38
- Guide from £205
Bespoke mirrors across Carrickfergus
To protect the edges, spray glass cleaner onto a soft cloth rather than directly onto the mirror, so liquid does not run down and soak into the bottom edge. Avoid harsh or abrasive cleaners, and dry the edges after cleaning in bathrooms.
Edge finish affects both look and safety. Flat polished edges suit frameless mirrors and mirror walls, bevelled edges add an angled border that catches the light, and a simple arrised edge takes the sharpness off edges that will be hidden by a frame or channel.
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
What you get
- Safety backing film where the position calls for it
- Mirror cut to size with your chosen edge finish
- Final clean and advice on protecting the edges
- Survey, measuring or templating of the wall or recess
Carrickfergus at a glance
- Postcodes covered
- BT38 and the surrounding area, including Holywood, Newtownabbey and Bangor (County Down)
- Coast
- Carrickfergus is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Carrickfergus the midwinter sun reaches about 12° above the horizon at noon, with roughly 7.0 hours of daylight, rising to about 59° and 17.0 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in Northern Ireland
- Technical Booklet V covers safety glazing in Northern Ireland, including glass in and around doors and low-level glazing where people could walk into it.
Guide prices in Carrickfergus
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Bespoke Mirrors in Carrickfergus: questions
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
Do you cover Carrickfergus for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Carrickfergus and the surrounding County Antrim area, including postcode districts BT38, and nearby Holywood, Newtownabbey and Bangor (County Down). Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Carrickfergus
Get a written quote in Carrickfergus
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.