Stalybridge · Greater Manchester
Bespoke Mirrors in Stalybridge
An awkward alcove or sloping ceiling in Stalybridge does not have to rule out a mirror, because each one we fit is templated and cut to the real shape of the space.
- SK15
- SK16
- OL6
- Guide from £205
Made to measure mirrors in Stalybridge: what to know
In bathrooms, good ventilation does more to protect a mirror than anything else, because steam and condensation reach the edges and backing. A heated demister pad behind the mirror keeps it clear after showers, but it needs wiring by a qualified electrician.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
A bonded mirror follows the surface behind it, so an uneven wall can bend the reflection. We check flatness at survey, and on uneven plaster or stone walls the mirror may need a flat backing board or the wall levelling first to avoid a wavy, distorted image.
What a typical job includes
- Mirror cut to size with your chosen edge finish
- Fixing with mirror-compatible adhesive, clips or channels
- Cut-outs and drilled holes for sockets, switches or fixings
- Final clean and advice on protecting the edges
Working in Stalybridge
- Postcodes covered
- SK15, SK16, OL6 and the surrounding area, including Dukinfield, Ashton-under-Lyne and Hyde
- Coast
- Stalybridge is well inland, around 49 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Stalybridge the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.2 hours of daylight, rising to about 60° and 16.8 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Stalybridge
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Stalybridge: questions
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
Do you cover Stalybridge for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Stalybridge and the surrounding Greater Manchester area, including postcode districts SK15, SK16 and OL6, and nearby Dukinfield, Ashton-under-Lyne and Hyde. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Stalybridge
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.