Winchester · Hampshire
Bespoke Mirrors in Winchester
Bespoke mirrors in Winchester start with a survey of the wall and its flatness, followed by a written quote that fixes the price for the mirror, edges and fixing shown.
- SO21
- SO22
- SO23
- Guide from £205
Winchester: made to measure mirrors
A bonded mirror follows the surface behind it, so an uneven wall can bend the reflection. We check flatness at survey, and on uneven plaster or stone walls the mirror may need a flat backing board or the wall levelling first to avoid a wavy, distorted image.
To protect the edges, spray glass cleaner onto a soft cloth rather than directly onto the mirror, so liquid does not run down and soak into the bottom edge. Avoid harsh or abrasive cleaners, and dry the edges after cleaning in bathrooms.
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
Included as standard
- Final clean and advice on protecting the edges
- Safety backing film where the position calls for it
- Survey, measuring or templating of the wall or recess
- Cut-outs and drilled holes for sockets, switches or fixings
Working in Winchester
- Postcodes covered
- SO21, SO22, SO23 and the surrounding area, including Eastleigh, Southampton and Totton
- Coast
- Winchester sits roughly 19 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Winchester the midwinter sun reaches about 16° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 62° and 16.3 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Winchester
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Safety-backed mirror
Mirror with a bonded backing film that holds fragments together if it breaks, recommended for doors, full-height mirrors, gyms and children's rooms.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Winchester: questions
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
What affects the cost of a bespoke mirror?
The main cost drivers are the size and thickness of the mirror, the number of panels, the edge finish, any tint or low-iron glass, safety backing, cut-outs and the fixing method. Very large single sheets, access through narrow stairs and full mirror walls also affect the price. See the guide prices for typical ranges.
Do you cover Winchester for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Winchester and the surrounding Hampshire area, including postcode districts SO21, SO22 and SO23, and nearby Eastleigh, Southampton and Totton. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Winchester
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.