Borehamwood · Hertfordshire
Bespoke Mirrors in Borehamwood
Bespoke mirrors in Borehamwood start with a survey of the wall and its flatness, followed by a written quote that fixes the price for the mirror, edges and fixing shown.
- WD6
- Guide from £205
Made to measure mirrors across Borehamwood
Templating lets a mirror follow sloping ceilings, curved alcoves, skirting lines and fitted furniture. Cut-outs for sockets and switches are marked on the template, and the faceplates are removed and refitted so the mirror sits neatly behind them.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
The price depends on mirror size and thickness, the number of panels, the edge finish, tint or low-iron glass, safety backing, cut-outs and the fixing method. Gym walls, very large single sheets and difficult access also affect cost. See the guide prices for typical ranges.
What you get
- Mirror cut to size with your chosen edge finish
- Safety backing film where the position calls for it
- Cut-outs and drilled holes for sockets, switches or fixings
- Final clean and advice on protecting the edges
Borehamwood at a glance
- Postcodes covered
- WD6 and the surrounding area, including Barnet, Bushey and Potters Bar
- Coast
- Borehamwood is well inland, around 50 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Borehamwood the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Borehamwood
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Clear silver mirror
Standard silver-coated float glass mirror, cut to size, suited to most rooms, wardrobes and wall mirrors where a true, neutral reflection is wanted.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bespoke Mirrors in Borehamwood: questions
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
What edge finishes can I choose for a bespoke mirror?
The main choices are a flat polished edge, a bevelled edge and an arrised edge. Polished edges give a clean, frameless look and suit mirror walls, bevels add an angled border that catches the light, and arrised edges simply take off the sharpness where a frame or channel will hide them. Bevel width can usually be chosen too.
What affects the cost of a bespoke mirror?
The main cost drivers are the size and thickness of the mirror, the number of panels, the edge finish, any tint or low-iron glass, safety backing, cut-outs and the fixing method. Very large single sheets, access through narrow stairs and full mirror walls also affect the price. See the guide prices for typical ranges.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Do you cover Borehamwood for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Borehamwood and the surrounding Hertfordshire area, including postcode districts WD6, and nearby Barnet, Bushey and Potters Bar. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Borehamwood
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.