Ormskirk · Lancashire
Bespoke Mirrors in Ormskirk
Looking for a bespoke mirror in Ormskirk? Our glaziers can measure your wall, alcove or wardrobe and quote for a mirror cut to size with the edge finish you choose.
- L39
- WN8
- Guide from £205
Made to measure mirrors in Ormskirk
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
To protect the edges, spray glass cleaner onto a soft cloth rather than directly onto the mirror, so liquid does not run down and soak into the bottom edge. Avoid harsh or abrasive cleaners, and dry the edges after cleaning in bathrooms.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
Included as standard
- Safety backing film where the position calls for it
- Cut-outs and drilled holes for sockets, switches or fixings
- Survey, measuring or templating of the wall or recess
- Fixing with mirror-compatible adhesive, clips or channels
About Ormskirk for this job
- Postcodes covered
- L39, WN8 and the surrounding area, including Maghull, Skelmersdale and Kirkby
- Coast
- Ormskirk sits roughly 14 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Ormskirk the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.2 hours of daylight, rising to about 60° and 16.8 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Ormskirk
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Options to choose between
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Clear silver mirror
Standard silver-coated float glass mirror, cut to size, suited to most rooms, wardrobes and wall mirrors where a true, neutral reflection is wanted.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Ormskirk: questions
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
What is a safety-backed mirror and do I need one?
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks. You should consider one wherever someone could knock or fall against the mirror, such as wardrobe doors, full-height mirrors, gyms, dance studios and children's rooms. We recommend it at survey when the position or use of the room calls for it.
Do you cover Ormskirk for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Ormskirk and the surrounding Lancashire area, including postcode districts L39 and WN8, and nearby Maghull, Skelmersdale and Kirkby. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Ormskirk
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.