Poulton-le-Fylde · Lancashire
Bespoke Mirrors in Poulton-le-Fylde
Do your sliding wardrobe doors in Poulton-le-Fylde need new mirror panels? We can measure, cut and fit safety-backed mirror to suit the existing door frames.
- FY3
- FY2
- FY6
- Guide from £205
Bespoke mirrors for homes and businesses in Poulton-le-Fylde
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
The price depends on mirror size and thickness, the number of panels, the edge finish, tint or low-iron glass, safety backing, cut-outs and the fixing method. Gym walls, very large single sheets and difficult access also affect cost. See the guide prices for typical ranges.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
Templating lets a mirror follow sloping ceilings, curved alcoves, skirting lines and fitted furniture. Cut-outs for sockets and switches are marked on the template, and the faceplates are removed and refitted so the mirror sits neatly behind them.
What a typical job includes
- Safety backing film where the position calls for it
- Final clean and advice on protecting the edges
- Cut-outs and drilled holes for sockets, switches or fixings
- Mirror cut to size with your chosen edge finish
Poulton-le-Fylde at a glance
- Postcodes covered
- FY3, FY2, FY6 and the surrounding area, including Blackpool, Thornton-Cleveleys and Lytham St Annes
- Coast
- Poulton-le-Fylde is about 6 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Poulton-le-Fylde the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.1 hours of daylight, rising to about 60° and 16.9 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Poulton-le-Fylde
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Safety-backed mirror
Mirror with a bonded backing film that holds fragments together if it breaks, recommended for doors, full-height mirrors, gyms and children's rooms.
Bespoke Mirrors in Poulton-le-Fylde: questions
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
What edge finishes can I choose for a bespoke mirror?
The main choices are a flat polished edge, a bevelled edge and an arrised edge. Polished edges give a clean, frameless look and suit mirror walls, bevels add an angled border that catches the light, and arrised edges simply take off the sharpness where a frame or channel will hide them. Bevel width can usually be chosen too.
Do you cover Poulton-le-Fylde for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Poulton-le-Fylde and the surrounding Lancashire area, including postcode districts FY3, FY2 and FY6, and nearby Blackpool, Thornton-Cleveleys and Lytham St Annes. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Poulton-le-Fylde
Get a written quote in Poulton-le-Fylde
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.