Maesteg · Mid Glamorgan
Bespoke Mirrors in Maesteg
Bespoke mirrors in Maesteg start with a survey of the wall and its flatness, followed by a written quote that fixes the price for the mirror, edges and fixing shown.
- CF34
- Guide from £205
Mirror cut to size in Maesteg
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
To protect the edges, spray glass cleaner onto a soft cloth rather than directly onto the mirror, so liquid does not run down and soak into the bottom edge. Avoid harsh or abrasive cleaners, and dry the edges after cleaning in bathrooms.
Included as standard
- Fixing with mirror-compatible adhesive, clips or channels
- Safety backing film where the position calls for it
- Survey, measuring or templating of the wall or recess
- Mirror cut to size with your chosen edge finish
About Maesteg for this job
- Postcodes covered
- CF34 and the surrounding area, including Aberkenfig, Pyle and Briton Ferry
- Coast
- Maesteg sits roughly 10 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Maesteg the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in Wales
- In Wales, Approved Document N covers safety glazing: safety glass is needed in and around doors and in low-level glazing where people could walk into it.
Guide prices in Maesteg
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Options to choose between
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bespoke Mirrors in Maesteg: questions
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
How long does a bespoke mirror take?
Plain mirrors cut to size are often ready soon after measuring, while bevelled, tinted, safety-backed or shaped mirrors take longer to process. Fitting is usually completed in a single visit, though full gym or studio walls can take longer. Your written quote sets out the expected timescale, and we confirm the date when the mirror is ready.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
What affects the cost of a bespoke mirror?
The main cost drivers are the size and thickness of the mirror, the number of panels, the edge finish, any tint or low-iron glass, safety backing, cut-outs and the fixing method. Very large single sheets, access through narrow stairs and full mirror walls also affect the price. See the guide prices for typical ranges.
Do you cover Maesteg for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Maesteg and the surrounding Mid Glamorgan area, including postcode districts CF34, and nearby Aberkenfig, Pyle and Briton Ferry. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Maesteg
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.