Henley-on-Thames · Oxfordshire
Bespoke Mirrors in Henley-on-Thames
Our glaziers fit bespoke mirrors in Henley-on-Thames for homes and businesses, including tinted, antique-effect and bevelled mirrors cut around sockets and fitted furniture.
- RG9
- Guide from £205
Henley-on-Thames: mirror cut to size
A bonded mirror follows the surface behind it, so an uneven wall can bend the reflection. We check flatness at survey, and on uneven plaster or stone walls the mirror may need a flat backing board or the wall levelling first to avoid a wavy, distorted image.
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
Included as standard
- Mirror cut to size with your chosen edge finish
- Safety backing film where the position calls for it
- Final clean and advice on protecting the edges
- Fixing with mirror-compatible adhesive, clips or channels
About Henley-on-Thames for this job
- Postcodes covered
- RG9 and the surrounding area, including Reading, Earley and Maidenhead
- Coast
- Henley-on-Thames is well inland, around 76 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Henley-on-Thames the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Henley-on-Thames
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Specification choices
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Safety-backed mirror
Mirror with a bonded backing film that holds fragments together if it breaks, recommended for doors, full-height mirrors, gyms and children's rooms.
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Bespoke Mirrors in Henley-on-Thames: questions
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
How long does a bespoke mirror take?
Plain mirrors cut to size are often ready soon after measuring, while bevelled, tinted, safety-backed or shaped mirrors take longer to process. Fitting is usually completed in a single visit, though full gym or studio walls can take longer. Your written quote sets out the expected timescale, and we confirm the date when the mirror is ready.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Do you cover Henley-on-Thames for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Henley-on-Thames and the surrounding Oxfordshire area, including postcode districts RG9, and nearby Reading, Earley and Maidenhead. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Henley-on-Thames
Get a written quote in Henley-on-Thames
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.