Aldridge · West Midlands
Bespoke Mirrors in Aldridge
Do your sliding wardrobe doors in Aldridge need new mirror panels? We can measure, cut and fit safety-backed mirror to suit the existing door frames.
- WS9
- Guide from £205
About wardrobe mirror doors in Aldridge
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
In bathrooms, good ventilation does more to protect a mirror than anything else, because steam and condensation reach the edges and backing. A heated demister pad behind the mirror keeps it clear after showers, but it needs wiring by a qualified electrician.
Edge finish affects both look and safety. Flat polished edges suit frameless mirrors and mirror walls, bevelled edges add an angled border that catches the light, and a simple arrised edge takes the sharpness off edges that will be hidden by a frame or channel.
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
What you get
- Fixing with mirror-compatible adhesive, clips or channels
- Survey, measuring or templating of the wall or recess
- Final clean and advice on protecting the edges
- Safety backing film where the position calls for it
Working in Aldridge
- Postcodes covered
- WS9 and the surrounding area, including Walsall, Bloxwich and Sutton Coldfield
- Coast
- Aldridge is well inland, around 97 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Aldridge the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.4 hours of daylight, rising to about 61° and 16.6 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Aldridge
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Specification choices
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Clear silver mirror
Standard silver-coated float glass mirror, cut to size, suited to most rooms, wardrobes and wall mirrors where a true, neutral reflection is wanted.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bespoke Mirrors in Aldridge: questions
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
What edge finishes can I choose for a bespoke mirror?
The main choices are a flat polished edge, a bevelled edge and an arrised edge. Polished edges give a clean, frameless look and suit mirror walls, bevels add an angled border that catches the light, and arrised edges simply take off the sharpness where a frame or channel will hide them. Bevel width can usually be chosen too.
Do you cover Aldridge for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Aldridge and the surrounding West Midlands area, including postcode districts WS9, and nearby Walsall, Bloxwich and Sutton Coldfield. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Aldridge
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.