Stourport-on-Severn · Worcestershire
Bespoke Mirrors in Stourport-on-Severn
Mirrors with black edges in Stourport-on-Severn cannot be restored, but we can measure and replace them with new mirror bonded using a compatible adhesive to protect the silver.
- DY13
- Guide from £205
Bespoke mirrors in Stourport-on-Severn
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
Safety backing is a sensible choice wherever someone could fall or knock against a mirror, such as sliding wardrobe doors, full-height mirrors, children's rooms, gyms and dance studios. We recommend it at survey wherever the position or use of the room suggests it.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
A bonded mirror follows the surface behind it, so an uneven wall can bend the reflection. We check flatness at survey, and on uneven plaster or stone walls the mirror may need a flat backing board or the wall levelling first to avoid a wavy, distorted image.
Included as standard
- Survey, measuring or templating of the wall or recess
- Safety backing film where the position calls for it
- Final clean and advice on protecting the edges
- Mirror cut to size with your chosen edge finish
About Stourport-on-Severn for this job
- Postcodes covered
- DY13 and the surrounding area, including Kidderminster, Droitwich and Bromsgrove
- Coast
- Stourport-on-Severn is well inland, around 62 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Stourport-on-Severn the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.4 hours of daylight, rising to about 61° and 16.6 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Stourport-on-Severn
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Choosing your bespoke mirrors
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Clear silver mirror
Standard silver-coated float glass mirror, cut to size, suited to most rooms, wardrobes and wall mirrors where a true, neutral reflection is wanted.
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Bespoke Mirrors in Stourport-on-Severn: questions
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
How long does a bespoke mirror take?
Plain mirrors cut to size are often ready soon after measuring, while bevelled, tinted, safety-backed or shaped mirrors take longer to process. Fitting is usually completed in a single visit, though full gym or studio walls can take longer. Your written quote sets out the expected timescale, and we confirm the date when the mirror is ready.
Do you cover Stourport-on-Severn for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Stourport-on-Severn and the surrounding Worcestershire area, including postcode districts DY13, and nearby Kidderminster, Droitwich and Bromsgrove. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Stourport-on-Severn
Get a written quote in Stourport-on-Severn
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.