Mold · Clwyd
Curtain Walling in Mold
Is water getting in around an older glazed facade in Mold? We can inspect gaskets, seals and drainage paths and quote for the repairs or replacement needed.
- CH7
- Guide from £455 per m²
Curtain wall glass replacement in Mold: what to know
Toughened glass can very occasionally break on its own because of nickel sulphide inclusions. Heat soak testing to BS EN 14179 reduces that risk by breaking flawed panes in the factory, and it is often specified for toughened glass high on facades where a breakage is harder to deal with.
Wind load on a facade rises with height, exposure and building shape, and it decides the mullion size, bracket design and glass thickness. Calculations for the specific site are part of the design, so a system suited to a sheltered ground-floor screen may not suit an exposed upper storey.
Building regulations require external walls to limit the spread of fire, so curtain walling design has to consider how its materials react to fire and how fire could pass between floors. The requirements depend on the building's height and use, and differ between the UK nations.
The price depends on the facade area, the system type, glass specification such as solar control or triple glazing, infill panels, opening vents, building height and access equipment, and design and testing requirements. Replacement units also depend on how the glass is retained. See the guide prices for typical ranges.
Included as standard
- Final inspection, clean and maintenance guidance
- Supply and installation of framing, glass and panels
- System selection and glass specification for the building
- Sealing, weathering and drainage details at all interfaces
Local details for Mold
- Postcodes covered
- CH7 and the surrounding area, including Buckley, Deeside and Hawarden
- Coast
- Mold sits roughly 10 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Facades near the sea face salt-laden wind and driving rain, which attack frame finishes and stress seals. Suitable coating specifications, regular washing, gasket checks and higher design wind loads for exposed sites all matter for curtain walling there.
- Daylight and sun
- In Mold the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Large glazed facades bring in plenty of daylight but also solar gain and glare, especially on south and west elevations. Solar control glass, shading and blinds are balanced against light transmission so interiors stay bright without overheating.
- Access and setting
- Commercial buildings on open rural or upland sites can face high wind exposure and driving rain, which affect frame sizes, glass thickness and sealing details. Longer delivery routes for large glass units also need planning in advance.
- Rules in Wales
- In Wales, Approved Document N covers safety glazing: safety glass is needed in and around doors and in low-level glazing where people could walk into it.
Guide prices in Mold
| Typical job | Guide price inc VAT |
|---|---|
| Curtain walling, per m² (stick system) | £455 – £795 |
| Curtain walling, per m² (unitised) | £545 – £955 |
Get a guide price for your size
Glass in a fire-resisting door or screen must be replaced with fire-rated glazing tested as part of that system. Ordinary toughened glass is not a substitute.
Specification choices
Integrated opening vents
Top-hung or parallel-opening vents built into the curtain wall grid to provide natural ventilation without breaking the facade line.
Solar control glass
Coated glass that limits solar heat gain on sunny elevations while keeping good daylight, reducing overheating and glare inside.
Unitised curtain wall
Factory-assembled, pre-glazed storey-height panels lifted into place, reducing site joints and work at height on taller or tight sites.
Curtain Walling in Mold: questions
How does curtain walling keep water out?
Curtain walling uses outer gaskets and seals to shed most rain, with drainage routes inside the framing that collect any water getting past them and lead it back outside. Inner seals then provide the air seal. Keeping drainage outlets clear and gaskets in good condition is essential, because blocked drains or shrunk seals can let water into the building.
Should I choose a stick or unitised curtain wall?
A stick system is assembled on site and generally suits low-rise buildings, entrances and smaller screens, with simpler logistics. A unitised system uses factory-made panels lifted into place, which reduces site joints and work at height but needs cranage and longer planning. The building's height, access and programme usually decide which is the right fit.
How should curtain walling be maintained?
Curtain walling should be cleaned regularly and inspected at planned intervals. Check that drainage outlets are clear, gaskets have not shrunk or slipped, sealant joints are intact and fixings show no corrosion. Address misted or cracked units early. A simple maintenance schedule kept with the building records helps facilities teams spot problems before they become leaks.
What is the difference between curtain walling and windows?
Curtain walling is a continuous framed wall of glass and panels that spans across floors and hangs off the building structure, carrying its own weight and wind loads. Windows sit within individual openings in a masonry or framed wall. Curtain walling suits large glazed areas and multi-storey facades, while windows suit punched openings.
Do you cover Mold for curtain walling?
Yes. We can quote for curtain walling across Mold and the surrounding Clwyd area, including postcode districts CH7, and nearby Buckley, Deeside and Hawarden. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Mold
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.