Ilford · Greater London
Curtain Walling in Ilford
Misted, cracked or leaking facade units in Ilford can usually be replaced individually, and we can survey the system and access before quoting.
- E18
- IG1
- IG2
- IG3
- IG4
- IG5
- Guide from £455 per m²
Curtain walling in Ilford: what to know
A unitised system arrives as storey-height panels assembled and glazed in a factory, which are lifted into place and interlocked. Fewer joints are made on site, which can reduce the risk of air and water leaks from site workmanship, but cranage and lead times need careful planning.
Wind load on a facade rises with height, exposure and building shape, and it decides the mullion size, bracket design and glass thickness. Calculations for the specific site are part of the design, so a system suited to a sheltered ground-floor screen may not suit an exposed upper storey.
The Centre for Window and Cladding Technology publishes the Standard for systemised building envelopes, the recognised UK industry standard for specifying, testing and assessing curtain walling. It draws in BS EN 13830 and the relevant building regulations, and is often referenced in commercial specifications.
A stick system is built on site piece by piece. Aluminium mullions and transoms are fixed to the structure first, then the glass and infill panels go in, and finally the pressure plates and caps. It suits low-rise buildings and screens but needs access to both faces.
Included as standard
- System selection and glass specification for the building
- Fabrication drawings and coordination with other trades
- Sealing, weathering and drainage details at all interfaces
- Final inspection, clean and maintenance guidance
Local details for Ilford
- Postcodes covered
- E18, IG1, IG2, IG3, IG4, IG5, IG6, IG8 and the surrounding area, including Barking, Becontree and Leytonstone
- Coast
- Ilford is well inland, around 24 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Ilford the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Large glazed facades bring in plenty of daylight but also solar gain and glare, especially on south and west elevations. Solar control glass, shading and blinds are balanced against light transmission so interiors stay bright without overheating.
- Access and setting
- City-centre facades often need crane or hoist bookings, pavement or road licences, out-of-hours deliveries and close coordination with other trades. Tight sites need careful sequencing, and unitised panels can reduce the amount of work at height.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Ilford
| Typical job | Guide price inc VAT |
|---|---|
| Curtain walling, per m² (stick system) | £455 – £795 |
| Curtain walling, per m² (unitised) | £545 – £955 |
Get a guide price for your size
Replacing windows and doors with similar ones is usually permitted development for houses in England. Flats, listed buildings and homes in conservation areas or covered by an Article 4 direction can need permission, so check with the council first.
Specification choices
Solar control glass
Coated glass that limits solar heat gain on sunny elevations while keeping good daylight, reducing overheating and glare inside.
Capped system
Glass clamped by pressure plates behind a visible external cap, available in different profiles and colours to emphasise the grid.
Opaque spandrel panels
Insulated or back-painted glass panels that hide floor slabs, ceiling voids and services while keeping the facade's appearance consistent.
Curtain Walling in Ilford: questions
What glass is used in curtain walling?
Curtain walling normally uses sealed double or triple glazed units, with toughened or laminated panes chosen for safety, security and wind load. Coatings control heat loss and solar gain, and heat-soaked toughened glass is often specified for upper levels. Where fire resistance is needed, a tested fire-resistant glazing system is used instead of standard glass.
Should I choose a stick or unitised curtain wall?
A stick system is assembled on site and generally suits low-rise buildings, entrances and smaller screens, with simpler logistics. A unitised system uses factory-made panels lifted into place, which reduces site joints and work at height but needs cranage and longer planning. The building's height, access and programme usually decide which is the right fit.
How should curtain walling be maintained?
Curtain walling should be cleaned regularly and inspected at planned intervals. Check that drainage outlets are clear, gaskets have not shrunk or slipped, sealant joints are intact and fixings show no corrosion. Address misted or cracked units early. A simple maintenance schedule kept with the building records helps facilities teams spot problems before they become leaks.
What affects the cost of curtain walling?
The main cost drivers are facade area, system type, glass specification, infill panels, opening vents, building height and access equipment such as scaffolding, hoists or cranes. Structural silicone glazing, unitised panels, fire-resisting sections and testing requirements add cost. See the guide prices for typical ranges, and your written quote fixes the price for the specification.
Do you cover Ilford for curtain walling?
Yes. We can quote for curtain walling across Ilford and the surrounding Greater London area, including postcode districts E18, IG1, IG2, IG3 and IG4, and nearby Barking, Becontree and Leytonstone. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Ilford
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.