Bristol · England
Glass Splashbacks in Bristol
A glass splashback in Bristol starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- Guide from £225
- Postcode areas BS
Bristol: coloured glass splashback
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
What applies in Bristol
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Parts of Bristol are within about 11 km of the coast, where exposure to wind and salt air is worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Bristol: questions
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Which parts of Bristol do you cover for glass splashbacks?
We cover the whole of Bristol, including postcode districts BS1, BS2, BS3, BS4, BS5, BS6, BS7 and BS8. Building rules for glass splashbacks here follow the regulations for England. Enter your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Bristol
- Replacement Glass in Bristol
- Misted Glass Repair in Bristol
- Emergency Glazing in Bristol
- Safety Glass in Bristol
- Window Repairs in Bristol
- Window Film in Bristol
- uPVC Windows in Bristol
- Aluminium Windows in Bristol
- Sash Windows in Bristol
- Composite Doors in Bristol
- Bifold Doors in Bristol
- Sliding Doors in Bristol
- Secondary Glazing in Bristol
- Roof Lanterns in Bristol
- Glass Balustrades in Bristol
- Frameless Glass in Bristol
- Shower Screens in Bristol
- Bespoke Mirrors in Bristol
- Glass Roofs in Bristol
- Shopfront Glazing in Bristol
- Curtain Walling in Bristol
- Glass Partitions in Bristol
- Property Glazing in Bristol
Get a written quote in Bristol
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.