Cambridge · Cambridgeshire
Glass Splashbacks in Cambridge
Fitting a new kitchen in Cambridge? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- CB2
- CB4
- CB1
- Guide from £225
Cambridge: glass splashbacks
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
What you get
- Back-painting to your chosen colour or finish
- Silicone-finished edges, final clean and care advice
- Bonding with adhesive compatible with the painted back
- Survey and templating after worktops and hob are fitted
Cambridge at a glance
- Postcodes covered
- CB2, CB4, CB1 and the surrounding area, including St Ives (Cambridgeshire), Newmarket and Ely
- Coast
- Cambridge is well inland, around 66 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Cambridge the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.5 hours of daylight, rising to about 61° and 16.5 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Cambridge
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Cambridge: questions
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Do you cover Cambridge for glass splashbacks?
Yes. We can quote for glass splashbacks across Cambridge and the surrounding Cambridgeshire area, including postcode districts CB2, CB4 and CB1, and nearby St Ives (Cambridgeshire), Newmarket and Ely. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Cambridge
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.