Stockton-on-Tees · County Durham
Glass Splashbacks in Stockton-on-Tees
We cover Stockton-on-Tees and County Durham for glass splashbacks in kitchens, utility rooms and bathrooms, with every job templated on site and quoted in writing before the glass is made.
- TS18
- TS19
- TS20
- Guide from £225
About glass splashbacks in Stockton-on-Tees
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
What's included
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
- Back-painting to your chosen colour or finish
- Removal and refitting of socket and switch faceplates
Stockton-on-Tees at a glance
- Postcodes covered
- TS18, TS19, TS20 and the surrounding area, including Billingham, Thornaby-on-Tees and Middlesbrough
- Coast
- Stockton-on-Tees sits roughly 10 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Stockton-on-Tees the midwinter sun reaches about 12° above the horizon at noon, with roughly 7.0 hours of daylight, rising to about 59° and 17.0 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Stockton-on-Tees
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Stockton-on-Tees: questions
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Do you cover Stockton-on-Tees for glass splashbacks?
Yes. We can quote for glass splashbacks across Stockton-on-Tees and the surrounding County Durham area, including postcode districts TS18, TS19 and TS20, and nearby Billingham, Thornaby-on-Tees and Middlesbrough. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Stockton-on-Tees
Get a written quote in Stockton-on-Tees
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.