Driffield · East Riding of Yorkshire
Glass Splashbacks in Driffield
Looking for a glass splashback in Driffield? Our glaziers can template your finished kitchen and quote for toughened, back-painted glass made with every socket cut-out in place.
- YO25
- Guide from £225
About toughened glass splashback in Driffield
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
What you get
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
- Survey and templating after worktops and hob are fitted
- Removal and refitting of socket and switch faceplates
Driffield at a glance
- Postcodes covered
- YO25 and the surrounding area, including Beverley, Bridlington and Cottingham
- Coast
- Driffield sits roughly 14 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Driffield the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.1 hours of daylight, rising to about 59° and 16.9 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Driffield
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Driffield: questions
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Driffield for glass splashbacks?
Yes. We can quote for glass splashbacks across Driffield and the surrounding East Riding of Yorkshire area, including postcode districts YO25, and nearby Beverley, Bridlington and Cottingham. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Driffield
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.