Edinburgh · Edinburgh & the Lothians
Glass Splashbacks in Edinburgh
Our glaziers fit back-painted glass splashbacks in Edinburgh, using low-iron glass for pale colours so whites and creams look true to the sample you chose.
- EH2
- EH3
- EH1
- Guide from £225
Edinburgh: kitchen glass splashback
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
What's included
- Removal and refitting of socket and switch faceplates
- Silicone-finished edges, final clean and care advice
- Bonding with adhesive compatible with the painted back
- Toughened glass made to template with factory cut-outs
Local details for Edinburgh
- Postcodes covered
- EH2, EH3, EH1 and the surrounding area, including Musselburgh, Dalkeith and Bonnyrigg
- Coast
- Edinburgh is about 4 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Edinburgh the midwinter sun reaches about 11° above the horizon at noon, with roughly 6.7 hours of daylight, rising to about 58° and 17.3 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in Scotland
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Edinburgh
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Edinburgh: questions
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Do you cover Edinburgh for glass splashbacks?
Yes. We can quote for glass splashbacks across Edinburgh and the surrounding Edinburgh & the Lothians area, including postcode districts EH2, EH3 and EH1, and nearby Musselburgh, Dalkeith and Bonnyrigg. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Edinburgh
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.