Barnes · Greater London
Glass Splashbacks in Barnes
A glass splashback in Barnes starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- SW13
- SW14
- W4
- Guide from £225
Toughened glass splashback in Barnes
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Colours look different on screens, in daylight and under kitchen lighting, so choose from a physical glass sample rather than a website or paint chart. We can match many paint and RAL colours, and a sample panel viewed in your own kitchen avoids surprises.
Included as standard
- Toughened glass made to template with factory cut-outs
- Survey and templating after worktops and hob are fitted
- Silicone-finished edges, final clean and care advice
- Bonding with adhesive compatible with the painted back
Working in Barnes
- Postcodes covered
- SW13, SW14, W4 and the surrounding area, including Chiswick, Putney and Hammersmith
- Coast
- Barnes is well inland, around 43 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Barnes the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Barnes
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Glass Splashbacks in Barnes: questions
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Do you cover Barnes for glass splashbacks?
Yes. We can quote for glass splashbacks across Barnes and the surrounding Greater London area, including postcode districts SW13, SW14 and W4, and nearby Chiswick, Putney and Hammersmith. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Barnes
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.