Edmonton · Greater London
Glass Splashbacks in Edmonton
Fitting a new kitchen in Edmonton? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- N9
- N18
- N21
- Guide from £225
Glass splashbacks for homes and businesses in Edmonton
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Included as standard
- Back-painting to your chosen colour or finish
- Survey and templating after worktops and hob are fitted
- Silicone-finished edges, final clean and care advice
- Toughened glass made to template with factory cut-outs
About Edmonton for this job
- Postcodes covered
- N9, N18, N21 and the surrounding area, including Tottenham, Enfield and Chingford
- Coast
- Edmonton is well inland, around 35 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Edmonton the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Edmonton
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Options to choose between
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Edmonton: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Edmonton for glass splashbacks?
Yes. We can quote for glass splashbacks across Edmonton and the surrounding Greater London area, including postcode districts N9, N18 and N21, and nearby Tottenham, Enfield and Chingford. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Edmonton
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.