Welling · Greater London
Glass Splashbacks in Welling
Looking for a glass splashback in Welling? Our glaziers can template your finished kitchen and quote for toughened, back-painted glass made with every socket cut-out in place.
- DA16
- DA6
- DA15
- Guide from £225
Welling: kitchen glass splashback
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
What you get
- Removal and refitting of socket and switch faceplates
- Silicone-finished edges, final clean and care advice
- Toughened glass made to template with factory cut-outs
- Bonding with adhesive compatible with the painted back
About Welling for this job
- Postcodes covered
- DA16, DA6, DA15 and the surrounding area, including Bexleyheath, Eltham and Thamesmead
- Coast
- Welling sits roughly 18 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Welling the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Welling
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Options to choose between
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Welling: questions
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Do you cover Welling for glass splashbacks?
Yes. We can quote for glass splashbacks across Welling and the surrounding Greater London area, including postcode districts DA16, DA6 and DA15, and nearby Bexleyheath, Eltham and Thamesmead. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Welling
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.