Welwyn Garden City · Hertfordshire
Glass Splashbacks in Welwyn Garden City
Is stained grout behind your hob in Welwyn Garden City hard to keep clean? We can replace tired tiles with a smooth, wipe-clean toughened glass panel in your chosen colour.
- AL7
- AL8
- Guide from £225
Toughened glass splashback in Welwyn Garden City
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
What's included
- Survey and templating after worktops and hob are fitted
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
- Removal and refitting of socket and switch faceplates
Working in Welwyn Garden City
- Postcodes covered
- AL7, AL8 and the surrounding area, including Hatfield, Hertford and St Albans
- Coast
- Welwyn Garden City is well inland, around 55 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Welwyn Garden City the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.5 hours of daylight, rising to about 62° and 16.5 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Welwyn Garden City
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Glass Splashbacks in Welwyn Garden City: questions
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Do you cover Welwyn Garden City for glass splashbacks?
Yes. We can quote for glass splashbacks across Welwyn Garden City and the surrounding Hertfordshire area, including postcode districts AL7 and AL8, and nearby Hatfield, Hertford and St Albans. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Welwyn Garden City
Get a written quote in Welwyn Garden City
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.