Isle of Wight · England
Glass Splashbacks in Isle of Wight
Is stained grout behind your hob in Isle of Wight hard to keep clean? We can replace tired tiles with a smooth, wipe-clean toughened glass panel in your chosen colour.
- Guide from £225
- 4 towns covered
- Postcode areas PO
About glass splashbacks in Isle of Wight
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Towns we cover for glass splashbacks in Isle of Wight
Choose your town for local details, nearby areas and the postcode districts we cover.
What applies in Isle of Wight
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Isle of Wight has its own coastline, so for homes and businesses near the sea, salt air and wind-driven rain are part of the brief. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Isle of Wight: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Which parts of Isle of Wight do you cover for glass splashbacks?
We cover the whole of Isle of Wight, including Newport (Isle of Wight), Ryde, Cowes and Sandown, and postcode areas PO. Building rules for glass splashbacks here follow the regulations for England. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Isle of Wight
- Replacement Glass in Isle of Wight
- Misted Glass Repair in Isle of Wight
- Emergency Glazing in Isle of Wight
- Safety Glass in Isle of Wight
- Window Repairs in Isle of Wight
- Window Film in Isle of Wight
- uPVC Windows in Isle of Wight
- Aluminium Windows in Isle of Wight
- Sash Windows in Isle of Wight
- Composite Doors in Isle of Wight
- Bifold Doors in Isle of Wight
- Sliding Doors in Isle of Wight
- Secondary Glazing in Isle of Wight
- Roof Lanterns in Isle of Wight
- Glass Balustrades in Isle of Wight
- Frameless Glass in Isle of Wight
- Shower Screens in Isle of Wight
- Bespoke Mirrors in Isle of Wight
- Glass Roofs in Isle of Wight
- Shopfront Glazing in Isle of Wight
- Curtain Walling in Isle of Wight
- Glass Partitions in Isle of Wight
- Property Glazing in Isle of Wight
All glazing in Isle of Wight · Glass Splashbacks across the UK
Get a written quote in Isle of Wight
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.