Merseyside · England
Glass Splashbacks in Merseyside
Fitting a new kitchen in Merseyside? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- Guide from £225
- 20 towns covered
- Postcode areas CH, L, PR, WA
Kitchen glass splashback for homes and businesses in Merseyside
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Towns we cover for glass splashbacks in Merseyside
Choose your town for local details, nearby areas and the postcode districts we cover.
What applies in Merseyside
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Merseyside has its own coastline, so for homes and businesses near the sea, salt air and wind-driven rain are part of the brief. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Glass Splashbacks in Merseyside: questions
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Which parts of Merseyside do you cover for glass splashbacks?
We cover the whole of Merseyside, including Liverpool, Birkenhead, St Helens, Southport and Wallasey, and postcode areas CH, L, PR, WA. Building rules for glass splashbacks here follow the regulations for England. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Merseyside
- Replacement Glass in Merseyside
- Misted Glass Repair in Merseyside
- Emergency Glazing in Merseyside
- Safety Glass in Merseyside
- Window Repairs in Merseyside
- Window Film in Merseyside
- uPVC Windows in Merseyside
- Aluminium Windows in Merseyside
- Sash Windows in Merseyside
- Composite Doors in Merseyside
- Bifold Doors in Merseyside
- Sliding Doors in Merseyside
- Secondary Glazing in Merseyside
- Roof Lanterns in Merseyside
- Glass Balustrades in Merseyside
- Frameless Glass in Merseyside
- Shower Screens in Merseyside
- Bespoke Mirrors in Merseyside
- Glass Roofs in Merseyside
- Shopfront Glazing in Merseyside
- Curtain Walling in Merseyside
- Glass Partitions in Merseyside
- Property Glazing in Merseyside
Get a written quote in Merseyside
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.