Market Drayton · Shropshire
Glass Splashbacks in Market Drayton
Is stained grout behind your hob in Market Drayton hard to keep clean? We can replace tired tiles with a smooth, wipe-clean toughened glass panel in your chosen colour.
- TF9
- Guide from £225
Coloured glass splashback in Market Drayton
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
What's included
- Removal and refitting of socket and switch faceplates
- Toughened glass made to template with factory cut-outs
- Bonding with adhesive compatible with the painted back
- Back-painting to your chosen colour or finish
Working in Market Drayton
- Postcodes covered
- TF9 and the surrounding area, including Newcastle-under-Lyme, Crewe and Wellington
- Coast
- Market Drayton is well inland, around 50 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Market Drayton the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Market Drayton
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Glass Splashbacks in Market Drayton: questions
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Do you cover Market Drayton for glass splashbacks?
Yes. We can quote for glass splashbacks across Market Drayton and the surrounding Shropshire area, including postcode districts TF9, and nearby Newcastle-under-Lyme, Crewe and Wellington. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Market Drayton
Get a written quote in Market Drayton
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.