Swansea · West Glamorgan
Glass Splashbacks in Swansea
A glass splashback in Swansea starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- SA1
- SA2
- SA5
- Guide from £225
Glass splashback behind hob for homes and businesses in Swansea
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
What you get
- Bonding with adhesive compatible with the painted back
- Removal and refitting of socket and switch faceplates
- Survey and templating after worktops and hob are fitted
- Toughened glass made to template with factory cut-outs
Local details for Swansea
- Postcodes covered
- SA1, SA2, SA5 and the surrounding area, including Clydach, Briton Ferry and Gorseinon
- Coast
- Swansea is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Swansea the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in Wales
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Swansea
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Glass Splashbacks in Swansea: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Swansea for glass splashbacks?
Yes. We can quote for glass splashbacks across Swansea and the surrounding West Glamorgan area, including postcode districts SA1, SA2 and SA5, and nearby Clydach, Briton Ferry and Gorseinon. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Swansea
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.