Stourbridge · West Midlands
Glass Splashbacks in Stourbridge
Fitting a new kitchen in Stourbridge? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- DY8
- DY9
- DY5
- Guide from £225
Glass splashbacks across Stourbridge
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Included as standard
- Silicone-finished edges, final clean and care advice
- Back-painting to your chosen colour or finish
- Bonding with adhesive compatible with the painted back
- Removal and refitting of socket and switch faceplates
Working in Stourbridge
- Postcodes covered
- DY8, DY9, DY5 and the surrounding area, including Brierley Hill, Kingswinford and Dudley
- Coast
- Stourbridge is well inland, around 76 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Stourbridge the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.4 hours of daylight, rising to about 61° and 16.6 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Stourbridge
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Stourbridge: questions
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Do you cover Stourbridge for glass splashbacks?
Yes. We can quote for glass splashbacks across Stourbridge and the surrounding West Midlands area, including postcode districts DY8, DY9 and DY5, and nearby Brierley Hill, Kingswinford and Dudley. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Stourbridge
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.