Yeadon · West Yorkshire
Glass Splashbacks in Yeadon
Our glaziers fit back-painted glass splashbacks in Yeadon, using low-iron glass for pale colours so whites and creams look true to the sample you chose.
- LS19
- LS20
- LS18
- Guide from £225
Kitchen glass splashback across Yeadon
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
What's included
- Toughened glass made to template with factory cut-outs
- Bonding with adhesive compatible with the painted back
- Silicone-finished edges, final clean and care advice
- Survey and templating after worktops and hob are fitted
Yeadon at a glance
- Postcodes covered
- LS19, LS20, LS18 and the surrounding area, including Guiseley, Shipley and Pudsey
- Coast
- Yeadon is well inland, around 66 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Yeadon the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.1 hours of daylight, rising to about 60° and 16.9 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Yeadon
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Yeadon: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Do you cover Yeadon for glass splashbacks?
Yes. We can quote for glass splashbacks across Yeadon and the surrounding West Yorkshire area, including postcode districts LS19, LS20 and LS18, and nearby Guiseley, Shipley and Pudsey. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Yeadon
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.