Sittingbourne · Kent
Safety Glass in Sittingbourne
Safety glass for doors, side panels and low windows in Sittingbourne can be made to the right class, with a permanent mark showing the standard.
- ME9
- ME10
- ME12
- Guide from £55
Toughened glass cut to size for homes and businesses in Sittingbourne
Laminated glass is two or more sheets bonded with a plastic interlayer, often PVB. If it breaks, the pieces stick to the interlayer and the pane stays in place. That makes it useful for overhead glass, ground-floor security and openings where an empty hole would be a risk.
In England, Approved Document K requires safety glass in critical locations: glass in a door or within 300mm of a door edge, up to 1500mm above the floor, and other glass within 800mm of the floor. The rules are similar elsewhere in the UK, but the detail differs.
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
Glass tabletops and shelves need the right thickness for the span and load. Thicker glass deflects less, so a long shelf or a large table needs a heavier panel than a small side table. The supplier confirms a suitable thickness for the use, not just the size.
What you get
- Advice on toughened or laminated glass for the location
- Glass cut, edge-worked and drilled before toughening
- Delivery or fitting by our glaziers
- Measurement or templating of the glass panel
Sittingbourne at a glance
- Postcodes covered
- ME9, ME10, ME12 and the surrounding area, including Faversham, Gillingham and Chatham
- Coast
- Sittingbourne sits roughly 6 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Near the coast, salt spray can mark exposed glass edges and corrode metal fixings. Polished edges and sealed laminated edges cope better outdoors, and stainless steel clamps and hinges are worth specifying for external safety glass panels and screens.
- Daylight and sun
- In Sittingbourne the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Sittingbourne
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Laminated safety glass
Two or more sheets bonded with an interlayer that holds broken glass in place, for overhead, security and fall-risk locations.
Polished edges
Smooth, clear edges for exposed glass on tables, shelves and frameless panels, safer to handle and neater to look at.
Safety Glass in Sittingbourne: questions
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
Do you cover Sittingbourne for safety glass?
Yes. We can quote for safety glass across Sittingbourne and the surrounding Kent area, including postcode districts ME9, ME10 and ME12, and nearby Faversham, Gillingham and Chatham. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Sittingbourne
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.