Kirkby-in-Ashfield · Nottinghamshire
Safety Glass in Kirkby-in-Ashfield
Safety glass for doors, side panels and low windows in Kirkby-in-Ashfield can be made to the right class, with a permanent mark showing the standard.
- NG17
- NG18
- Guide from £55
Laminated safety glass for homes and businesses in Kirkby-in-Ashfield
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
Toughened glass is ordinary float glass that has been cut to size, heated and then cooled quickly with jets of air. This leaves the surfaces in compression, making it several times stronger than untreated glass of the same thickness. When it does break, it crumbles into small, relatively blunt pieces.
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
BS EN 12600 classifies safety glass by a pendulum impact test, with class 1 the highest and class 3 the lowest. In England, critical locations generally need at least class 3, and door or side panels wider than 900mm need class 2 or better.
What you get
- Glass cut, edge-worked and drilled before toughening
- Delivery or fitting by our glaziers
- Advice on toughened or laminated glass for the location
- Measurement or templating of the glass panel
Working in Kirkby-in-Ashfield
- Postcodes covered
- NG17, NG18 and the surrounding area, including Sutton-in-Ashfield, Mansfield and Hucknall
- Coast
- Kirkby-in-Ashfield is well inland, around 76 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Kirkby-in-Ashfield the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- Older rural homes often have internal doors and screens with old, unmarked glass. Upgrading them to toughened or laminated safety glass is common, and timber door frames may need careful beading when the new glass is fitted.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Kirkby-in-Ashfield
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Clear toughened glass
Heat-treated float glass that breaks into small, blunt pieces, for doors, screens, tabletops and shelves in a range of thicknesses.
Holes and cut-outs
Drilled holes for handles, hinges and fixings, and cut-outs for sockets, all made before the glass is toughened.
Safety Glass in Kirkby-in-Ashfield: questions
Can toughened glass be cut or drilled after it is made?
No. Toughened glass cannot be cut, drilled or edge-worked once it has been toughened, because any damage to the surface releases the internal stress and the whole pane shatters. All sizes, holes and cut-outs must be finalised before toughening. That is why accurate measurements or a template are needed before the order is placed.
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
How much does toughened glass cut to size cost?
The price depends on the dimensions, thickness, glass type, edge finish, number of holes and cut-outs, any shapes, and whether you want supply only or fitting. Laminated, low-iron and obscure glass cost more than clear toughened. See the guide prices for typical panels, then get a written quote for your exact specification.
Do you cover Kirkby-in-Ashfield for safety glass?
Yes. We can quote for safety glass across Kirkby-in-Ashfield and the surrounding Nottinghamshire area, including postcode districts NG17 and NG18, and nearby Sutton-in-Ashfield, Mansfield and Hucknall. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Kirkby-in-Ashfield
Get a written quote in Kirkby-in-Ashfield
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.