Washington · Tyne and Wear
Safety Glass in Washington
Glass tabletops, shelves and splash panels for homes in Washington can be cut, polished and toughened to your exact size and shape.
- NE37
- NE38
- Guide from £55
Toughened glass panels for homes and businesses in Washington
Edge finish affects both look and safety. Arrised edges are lightly sanded to take off sharpness and suit glass held in frames. Polished edges are smooth and clear for exposed edges on tables, shelves and frameless panels. Bevelled edges add a decorative angled border.
Safety glass in a building should carry a permanent mark, usually in a corner, that stays visible after fitting. It names the maker or supplier and the standard, such as BS EN 12150 for toughened glass. The mark is how a buyer or inspector can confirm what was fitted.
Low-iron glass removes most of the slight green tint that ordinary clear glass shows at its edge and through thick panels. It suits tabletops, display shelves and splashback-style panels where true colours and a clearer edge matter.
When measuring for a replacement panel, measure the opening or old glass in at least two places for width and height, and note the thickness. For anything with holes, curves or angled corners, a hardboard or card template gives the most reliable result.
What's included
- Glass cut, edge-worked and drilled before toughening
- Permanent safety marking on building glass
- Measurement or templating of the glass panel
- Delivery or fitting by our glaziers
Washington at a glance
- Postcodes covered
- NE37, NE38 and the surrounding area, including Chester-le-Street, Felling and Houghton-le-Spring
- Coast
- Washington sits roughly 10 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Near the coast, salt spray can mark exposed glass edges and corrode metal fixings. Polished edges and sealed laminated edges cope better outdoors, and stainless steel clamps and hinges are worth specifying for external safety glass panels and screens.
- Daylight and sun
- In Washington the midwinter sun reaches about 12° above the horizon at noon, with roughly 6.9 hours of daylight, rising to about 58° and 17.1 hours in midsummer. Strong sun on large glass panels can cause glare and fade furniture behind them. Tinted, solar control or low-iron toughened glass each change how much light, heat and colour come through, so orientation is worth considering when choosing.
- Access and setting
- In flats and city buildings, large panels of safety glass may need to fit through narrow stairs, lifts and doorways. Measuring access routes at the survey avoids problems, and laminated glass suits ground-floor doors and screens facing the street.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Washington
| Typical job | Guide price inc VAT |
|---|---|
| 6 mm toughened panel, 800 × 600 mm | £55 – £75 |
| 10 mm toughened panel, 1000 × 2000 mm | £325 – £415 |
| Glass tabletop or shelf, 1200 × 600 mm, 8 mm | £135 – £165 |
| 6.4 mm laminated panel, 900 × 900 mm | £115 – £145 |
Get a guide price for your size
Approved Document Q applies to new homes in England, where doors and windows are expected to meet PAS 24 or an equivalent standard. It does not apply to replacements in existing homes, but PAS 24 products are still a sensible choice.
Choosing your safety glass
Satin or obscure finish
Acid-etched or patterned glass for privacy in doors and screens, toughened or laminated to meet safety requirements.
Toughened laminated glass
Toughened sheets laminated together, combining strength with post-breakage retention, often used for frameless panels and higher-load applications.
Polished edges
Smooth, clear edges for exposed glass on tables, shelves and frameless panels, safer to handle and neater to look at.
Safety Glass in Washington: questions
How do I know if my glass is safety glass?
Look for a permanent mark etched or printed in a corner of the pane. It should name the maker or supplier and the standard, such as BS EN 12150 for toughened glass, or show a BS EN 12600 class. Older glass may have no mark. If you are unsure, a glazier can check and advise.
Where is safety glass required in a house?
In England, safety glass is needed in critical locations: glass in doors and within 300mm of a door edge, up to 1500mm above floor level, and other glass within 800mm of the floor. Small panes and leaded lights have specific exceptions. The rules elsewhere in the UK are similar, but the detail differs between nations.
Should I choose a polished or arrised edge?
Choose polished edges where the edge will be seen or touched, such as tabletops, shelves and frameless panels, because they are smooth and look neat. Arrised edges are lightly sanded to remove sharpness and are fine where the edge sits hidden in a frame. Bevelled edges are decorative and suit mirrors and some tabletops.
What is the difference between toughened and laminated glass?
Toughened glass is heat treated so it is stronger and, if broken, crumbles into small, relatively blunt pieces, leaving the opening empty. Laminated glass is sheets bonded to an interlayer, so when it breaks the pieces stay stuck in place. Both can be safety glass. Laminated is preferred where falling glass or an open hole would be a hazard.
Do you cover Washington for safety glass?
Yes. We can quote for safety glass across Washington and the surrounding Tyne and Wear area, including postcode districts NE37 and NE38, and nearby Chester-le-Street, Felling and Houghton-le-Spring. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Washington
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.