Barnes · Greater London
Bespoke Mirrors in Barnes
Our glaziers fit bespoke mirrors in Barnes for homes and businesses, including tinted, antique-effect and bevelled mirrors cut around sockets and fitted furniture.
- SW13
- SW14
- W4
- Guide from £205
Wardrobe mirror doors across Barnes
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
Templating lets a mirror follow sloping ceilings, curved alcoves, skirting lines and fitted furniture. Cut-outs for sockets and switches are marked on the template, and the faceplates are removed and refitted so the mirror sits neatly behind them.
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
In bathrooms, good ventilation does more to protect a mirror than anything else, because steam and condensation reach the edges and backing. A heated demister pad behind the mirror keeps it clear after showers, but it needs wiring by a qualified electrician.
What you get
- Fixing with mirror-compatible adhesive, clips or channels
- Safety backing film where the position calls for it
- Final clean and advice on protecting the edges
- Cut-outs and drilled holes for sockets, switches or fixings
Working in Barnes
- Postcodes covered
- SW13, SW14, W4 and the surrounding area, including Chiswick, Putney and Hammersmith
- Coast
- Barnes is well inland, around 43 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Barnes the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Barnes
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Options to choose between
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Bespoke Mirrors in Barnes: questions
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Do you cover Barnes for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Barnes and the surrounding Greater London area, including postcode districts SW13, SW14 and W4, and nearby Chiswick, Putney and Hammersmith. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Barnes
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.