Hanworth · Greater London
Bespoke Mirrors in Hanworth
Mirrors with black edges in Hanworth cannot be restored, but we can measure and replace them with new mirror bonded using a compatible adhesive to protect the silver.
- TW13
- TW12
- TW2
- Guide from £205
About gym wall mirrors in Hanworth
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
The price depends on mirror size and thickness, the number of panels, the edge finish, tint or low-iron glass, safety backing, cut-outs and the fixing method. Gym walls, very large single sheets and difficult access also affect cost. See the guide prices for typical ranges.
Most mirrors for internal use are made from silver-coated float glass covered by BS EN 1036-1, which sets definitions, quality requirements and test methods, including resistance to damp and corrosion. Mirror for bathrooms or other humid areas should come from a supplier whose product meets that standard.
What you get
- Cut-outs and drilled holes for sockets, switches or fixings
- Final clean and advice on protecting the edges
- Survey, measuring or templating of the wall or recess
- Fixing with mirror-compatible adhesive, clips or channels
About Hanworth for this job
- Postcodes covered
- TW13, TW12, TW2 and the surrounding area, including Hampton, Feltham and Twickenham
- Coast
- Hanworth is well inland, around 52 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Hanworth the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Hanworth
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Hanworth: questions
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
Can I have a bespoke mirror in a bathroom?
Yes, provided the room is well ventilated and the mirror is protected from standing water. We use mirror that meets the relevant standard for internal use, bond it with a compatible adhesive and keep edges away from splashes where possible. A heated demister pad can keep part of the mirror clear, wired in by a qualified electrician.
How long does a bespoke mirror take?
Plain mirrors cut to size are often ready soon after measuring, while bevelled, tinted, safety-backed or shaped mirrors take longer to process. Fitting is usually completed in a single visit, though full gym or studio walls can take longer. Your written quote sets out the expected timescale, and we confirm the date when the mirror is ready.
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Do you cover Hanworth for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Hanworth and the surrounding Greater London area, including postcode districts TW13, TW12 and TW2, and nearby Hampton, Feltham and Twickenham. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Hanworth
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.