Broadstairs · Kent
Bespoke Mirrors in Broadstairs
Bespoke mirrors in Broadstairs start with a survey of the wall and its flatness, followed by a written quote that fixes the price for the mirror, edges and fixing shown.
- CT10
- Guide from £205
Made to measure mirrors in Broadstairs: what to know
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
The price depends on mirror size and thickness, the number of panels, the edge finish, tint or low-iron glass, safety backing, cut-outs and the fixing method. Gym walls, very large single sheets and difficult access also affect cost. See the guide prices for typical ranges.
To protect the edges, spray glass cleaner onto a soft cloth rather than directly onto the mirror, so liquid does not run down and soak into the bottom edge. Avoid harsh or abrasive cleaners, and dry the edges after cleaning in bathrooms.
What a typical job includes
- Cut-outs and drilled holes for sockets, switches or fixings
- Survey, measuring or templating of the wall or recess
- Final clean and advice on protecting the edges
- Mirror cut to size with your chosen edge finish
About Broadstairs for this job
- Postcodes covered
- CT10 and the surrounding area, including Ramsgate, Margate and Deal
- Coast
- Broadstairs is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Broadstairs the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Broadstairs
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
What you can choose
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Heated demister pad
A thin heating pad bonded behind a bathroom mirror to keep an area clear of steam, wired in by a qualified electrician.
Clear silver mirror
Standard silver-coated float glass mirror, cut to size, suited to most rooms, wardrobes and wall mirrors where a true, neutral reflection is wanted.
Bespoke Mirrors in Broadstairs: questions
How should I clean a mirror without damaging it?
Spray glass cleaner onto a soft, lint-free cloth rather than directly onto the mirror, then wipe and buff dry. That stops liquid running down and soaking into the bottom edge, which is where black edges usually start. Avoid abrasive pads and harsh chemical cleaners, and dry the edges after cleaning in bathrooms.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
Do you cover Broadstairs for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Broadstairs and the surrounding Kent area, including postcode districts CT10, and nearby Ramsgate, Margate and Deal. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Broadstairs
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.