Margate · Kent
Bespoke Mirrors in Margate
Our glaziers fit bespoke mirrors in Margate for homes and businesses, including tinted, antique-effect and bevelled mirrors cut around sockets and fitted furniture.
- CT8
- CT9
- CT11
- Guide from £205
Gym wall mirrors in Margate
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks, so fragments stay on the backing instead of falling or scattering. Some backing films are classified for impact under BS EN 12600, and the film is applied before fitting.
Large mirrors are usually fixed with mirror adhesive and supported at the base by a slim channel or clips while the adhesive cures and afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which also lets them be removed later.
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
Included as standard
- Mirror cut to size with your chosen edge finish
- Cut-outs and drilled holes for sockets, switches or fixings
- Survey, measuring or templating of the wall or recess
- Final clean and advice on protecting the edges
About Margate for this job
- Postcodes covered
- CT8, CT9, CT11 and the surrounding area, including Broadstairs, Ramsgate and Deal
- Coast
- Margate is about 2 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Mirrors are fitted indoors, but salty, humid coastal air can still reach the silver backing through exposed edges, particularly in bathrooms and near entrances. Protected edges, a compatible adhesive and good ventilation all help prevent black edge corrosion.
- Daylight and sun
- In Margate the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Large mirrors for flats, salons and gyms often have to travel through narrow stairwells and small lifts, so walls may be covered in several panels with planned joints. Loading limits and building working hours can affect fitting times.
- Rules in England
- Approved Document K requires safety glass in critical locations in England: glazing in doors and in side panels within 300 mm of a door, up to 1500 mm above floor level, and any glazing in walls or partitions up to 800 mm above floor level.
Guide prices in Margate
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Choosing your bespoke mirrors
Safety-backed mirror
Mirror with a bonded backing film that holds fragments together if it breaks, recommended for doors, full-height mirrors, gyms and children's rooms.
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Margate: questions
Can a mirror be cut around sockets and light switches?
Yes. We mark socket and switch positions on the template, cut the openings in the mirror, then remove and refit the faceplates so the mirror sits neatly behind them with the power isolated. If sockets need moving or adding, a qualified electrician should do that before we template so the cut-outs line up.
How is a large mirror fixed to the wall?
Large mirrors are usually bonded with an adhesive made for mirror backing and supported along the bottom edge by a slim channel or clips. The support carries the weight while the adhesive cures and adds security afterwards. Smaller mirrors can be screw-fixed through drilled holes with decorative caps, which makes them easier to remove later.
What is a safety-backed mirror and do I need one?
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks. You should consider one wherever someone could knock or fall against the mirror, such as wardrobe doors, full-height mirrors, gyms, dance studios and children's rooms. We recommend it at survey when the position or use of the room calls for it.
What edge finishes can I choose for a bespoke mirror?
The main choices are a flat polished edge, a bevelled edge and an arrised edge. Polished edges give a clean, frameless look and suit mirror walls, bevels add an angled border that catches the light, and arrised edges simply take off the sharpness where a frame or channel will hide them. Bevel width can usually be chosen too.
Do you cover Margate for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Margate and the surrounding Kent area, including postcode districts CT8, CT9 and CT11, and nearby Broadstairs, Ramsgate and Deal. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Margate
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.