Kilsyth · Lanarkshire
Bespoke Mirrors in Kilsyth
Mirrors with black edges in Kilsyth cannot be restored, but we can measure and replace them with new mirror bonded using a compatible adhesive to protect the silver.
- G65
- Guide from £205
Bespoke mirrors in Kilsyth: what to know
Black edges, often called edge creep, are corrosion of the silver layer, usually started by moisture or cleaning fluid getting into the edges, or by an unsuitable adhesive. Once the silver has corroded it cannot be restored, so the mirror has to be replaced.
A bonded mirror follows the surface behind it, so an uneven wall can bend the reflection. We check flatness at survey, and on uneven plaster or stone walls the mirror may need a flat backing board or the wall levelling first to avoid a wavy, distorted image.
Mirrors must be bonded with an adhesive made to be compatible with mirror backing. Some general-purpose adhesives and acidic sealants can attack the protective coatings and the silver, causing dark patches that spread from behind. We only use mirror-compatible products.
Edge finish affects both look and safety. Flat polished edges suit frameless mirrors and mirror walls, bevelled edges add an angled border that catches the light, and a simple arrised edge takes the sharpness off edges that will be hidden by a frame or channel.
What you get
- Final clean and advice on protecting the edges
- Survey, measuring or templating of the wall or recess
- Safety backing film where the position calls for it
- Fixing with mirror-compatible adhesive, clips or channels
Working in Kilsyth
- Postcodes covered
- G65 and the surrounding area, including Cumbernauld, Kirkintilloch and Bishopbriggs
- Coast
- Kilsyth is well inland, around 21 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Kilsyth the midwinter sun reaches about 11° above the horizon at noon, with roughly 6.7 hours of daylight, rising to about 58° and 17.3 hours in midsummer. A mirror opposite or beside a window reflects daylight deeper into a room, which helps dark north-facing spaces through winter. Low direct sun on a large mirror can cause glare, so its position and any tint are worth considering.
- Access and setting
- Older rural homes often have uneven walls of stone or lime plaster, which can distort a bonded mirror unless the wall is levelled or a backing board is used. Damp solid walls also need checking before a mirror is fixed to them.
- Rules in Scotland
- Section 4 (Safety) of the Scottish Technical Handbooks covers glazing that people could collide with, such as glass in and beside doors and low-level glazing, where safety glass is needed.
Guide prices in Kilsyth
| Typical job | Guide price inc VAT |
|---|---|
| Polished mirror, 1200 × 900 mm | £205 – £265 |
| Safety-backed mirror, 1800 × 1000 mm | £365 – £465 |
| Gym mirror wall, 4000 × 2000 mm | £995 – £1,295 |
Options to choose between
Low-iron mirror
Mirror made on low-iron glass, which reduces the slight green cast of standard glass for a brighter, more colour-accurate reflection.
Tinted mirror
Grey or bronze tinted mirror that softens the reflection and adds warmth or depth, often used as a feature wall or in hospitality spaces.
Bevelled edge
An angled border ground and polished around the edge that catches the light and frames the mirror without needing a separate frame.
Bespoke Mirrors in Kilsyth: questions
Can a large mirror be fixed to plasterboard?
Often, yes, but it depends on the board, its fixings and the surface finish. Adhesive grips the paint or plaster layer, so flaky paint or weak skim can let go under the weight. We check the wall at survey and may add a base channel, mechanical fixings into studs, or a backing board to spread the load.
Why do mirrors go black around the edges?
Black edges are corrosion of the silver layer behind the glass, usually caused by moisture or cleaning fluid getting into the edges, or by an adhesive that reacts with the backing. Bathrooms are especially at risk because of steam. The damage cannot be reversed, so the mirror needs replacing, ideally with better edge protection and a compatible adhesive.
What is a safety-backed mirror and do I need one?
A safety-backed mirror has a film bonded across its back that holds the pieces together if the glass breaks. You should consider one wherever someone could knock or fall against the mirror, such as wardrobe doors, full-height mirrors, gyms, dance studios and children's rooms. We recommend it at survey when the position or use of the room calls for it.
How long does a bespoke mirror take?
Plain mirrors cut to size are often ready soon after measuring, while bevelled, tinted, safety-backed or shaped mirrors take longer to process. Fitting is usually completed in a single visit, though full gym or studio walls can take longer. Your written quote sets out the expected timescale, and we confirm the date when the mirror is ready.
Do you cover Kilsyth for bespoke mirrors?
Yes. We can quote for bespoke mirrors across Kilsyth and the surrounding Lanarkshire area, including postcode districts G65, and nearby Cumbernauld, Kirkintilloch and Bishopbriggs. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Kilsyth
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.