Ayrshire · Scotland
Glass Splashbacks in Ayrshire
Fitting a new kitchen in Ayrshire? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- Guide from £225
- 9 towns covered
- Postcode areas KA, PA
Glass splashbacks in Ayrshire
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Towns we cover for glass splashbacks in Ayrshire
Choose your town for local details, nearby areas and the postcode districts we cover.
What applies in Ayrshire
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Ayrshire has its own coastline, so for homes and businesses near the sea, salt air and wind-driven rain are part of the brief. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Glass Splashbacks in Ayrshire: questions
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Which parts of Ayrshire do you cover for glass splashbacks?
We cover the whole of Ayrshire, including Kilmarnock, Ayr, Irvine, Kilwinning and Troon, and postcode areas KA, PA. Building rules for glass splashbacks here follow the regulations for Scotland. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in Ayrshire
- Replacement Glass in Ayrshire
- Misted Glass Repair in Ayrshire
- Emergency Glazing in Ayrshire
- Safety Glass in Ayrshire
- Window Repairs in Ayrshire
- Window Film in Ayrshire
- uPVC Windows in Ayrshire
- Aluminium Windows in Ayrshire
- Sash Windows in Ayrshire
- Composite Doors in Ayrshire
- Bifold Doors in Ayrshire
- Sliding Doors in Ayrshire
- Secondary Glazing in Ayrshire
- Roof Lanterns in Ayrshire
- Glass Balustrades in Ayrshire
- Frameless Glass in Ayrshire
- Shower Screens in Ayrshire
- Bespoke Mirrors in Ayrshire
- Glass Roofs in Ayrshire
- Shopfront Glazing in Ayrshire
- Curtain Walling in Ayrshire
- Glass Partitions in Ayrshire
- Property Glazing in Ayrshire
Get a written quote in Ayrshire
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.