Saltcoats · Ayrshire
Glass Splashbacks in Saltcoats
Our glaziers fit back-painted glass splashbacks in Saltcoats, using low-iron glass for pale colours so whites and creams look true to the sample you chose.
- KA21
- KA22
- KA20
- Guide from £225
Glass splashback behind hob across Saltcoats
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
What a typical job includes
- Toughened glass made to template with factory cut-outs
- Survey and templating after worktops and hob are fitted
- Silicone-finished edges, final clean and care advice
- Back-painting to your chosen colour or finish
About Saltcoats for this job
- Postcodes covered
- KA21, KA22, KA20 and the surrounding area, including Ardrossan, Kilwinning and Irvine
- Coast
- Saltcoats is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Saltcoats the midwinter sun reaches about 11° above the horizon at noon, with roughly 6.8 hours of daylight, rising to about 58° and 17.2 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Scotland
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Saltcoats
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Saltcoats: questions
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Do you cover Saltcoats for glass splashbacks?
Yes. We can quote for glass splashbacks across Saltcoats and the surrounding Ayrshire area, including postcode districts KA21, KA22 and KA20, and nearby Ardrossan, Kilwinning and Irvine. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
More glazing in Saltcoats
Glass Splashbacks nearby
Get a written quote in Saltcoats
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.