Macclesfield · Cheshire
Glass Splashbacks in Macclesfield
Fitting a new kitchen in Macclesfield? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- SK9
- SK10
- SK11
- Guide from £225
About glass splashback behind hob in Macclesfield
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Included as standard
- Bonding with adhesive compatible with the painted back
- Removal and refitting of socket and switch faceplates
- Toughened glass made to template with factory cut-outs
- Back-painting to your chosen colour or finish
Macclesfield at a glance
- Postcodes covered
- SK9, SK10, SK11 and the surrounding area, including Wilmslow, Congleton and Cheadle Hulme
- Coast
- Macclesfield is well inland, around 43 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Macclesfield the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Macclesfield
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Glass Splashbacks in Macclesfield: questions
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Do you cover Macclesfield for glass splashbacks?
Yes. We can quote for glass splashbacks across Macclesfield and the surrounding Cheshire area, including postcode districts SK9, SK10 and SK11, and nearby Wilmslow, Congleton and Cheadle Hulme. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Macclesfield
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.