Hawarden · Clwyd
Glass Splashbacks in Hawarden
A glass splashback in Hawarden starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- CH5
- Guide from £225
Toughened glass splashback in Hawarden: what to know
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
What you get
- Back-painting to your chosen colour or finish
- Toughened glass made to template with factory cut-outs
- Survey and templating after worktops and hob are fitted
- Removal and refitting of socket and switch faceplates
Local details for Hawarden
- Postcodes covered
- CH5 and the surrounding area, including Deeside, Buckley and Mold
- Coast
- Hawarden sits roughly 9 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Hawarden the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.3 hours of daylight, rising to about 60° and 16.7 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Wales
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Hawarden
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Options to choose between
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Glass Splashbacks in Hawarden: questions
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
Do you cover Hawarden for glass splashbacks?
Yes. We can quote for glass splashbacks across Hawarden and the surrounding Clwyd area, including postcode districts CH5, and nearby Deeside, Buckley and Mold. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Hawarden
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.