County Tyrone · Northern Ireland
Glass Splashbacks in County Tyrone
Our glaziers fit back-painted glass splashbacks in County Tyrone, using low-iron glass for pale colours so whites and creams look true to the sample you chose.
- Guide from £225
- 4 towns covered
- Postcode areas BT
Toughened glass splashback in County Tyrone: what to know
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
What applies in County Tyrone
Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Parts of County Tyrone are within about 20 km of the coast, where exposure to wind and salt air is worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
Guide prices
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in County Tyrone: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Which parts of County Tyrone do you cover for glass splashbacks?
We cover the whole of County Tyrone, including Omagh, Strabane, Dungannon and Cookstown, and postcode areas BT. Building rules for glass splashbacks here follow the regulations for Northern Ireland. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.
Other glazing services in County Tyrone
- Replacement Glass in County Tyrone
- Misted Glass Repair in County Tyrone
- Emergency Glazing in County Tyrone
- Safety Glass in County Tyrone
- Window Repairs in County Tyrone
- Window Film in County Tyrone
- uPVC Windows in County Tyrone
- Aluminium Windows in County Tyrone
- Sash Windows in County Tyrone
- Composite Doors in County Tyrone
- Bifold Doors in County Tyrone
- Sliding Doors in County Tyrone
- Secondary Glazing in County Tyrone
- Roof Lanterns in County Tyrone
- Glass Balustrades in County Tyrone
- Frameless Glass in County Tyrone
- Shower Screens in County Tyrone
- Bespoke Mirrors in County Tyrone
- Glass Roofs in County Tyrone
- Shopfront Glazing in County Tyrone
- Curtain Walling in County Tyrone
- Glass Partitions in County Tyrone
- Property Glazing in County Tyrone
All glazing in County Tyrone · Glass Splashbacks across the UK
Get a written quote in County Tyrone
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.