Aberystwyth · Dyfed
Glass Splashbacks in Aberystwyth
Looking for a glass splashback in Aberystwyth? Our glaziers can template your finished kitchen and quote for toughened, back-painted glass made with every socket cut-out in place.
- SY23
- Guide from £225
Toughened glass splashback in Aberystwyth: what to know
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
What's included
- Back-painting to your chosen colour or finish
- Survey and templating after worktops and hob are fitted
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
About Aberystwyth for this job
- Postcodes covered
- SY23 and the surrounding area, including Dolgellau, Llandrindod Wells and Cardigan
- Coast
- Aberystwyth is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Aberystwyth the midwinter sun reaches about 14° above the horizon at noon, with roughly 7.4 hours of daylight, rising to about 61° and 16.6 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Wales
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Aberystwyth
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Choosing your glass splashbacks
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Aberystwyth: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Aberystwyth for glass splashbacks?
Yes. We can quote for glass splashbacks across Aberystwyth and the surrounding Dyfed area, including postcode districts SY23, and nearby Dolgellau, Llandrindod Wells and Cardigan. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Aberystwyth
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.