Brighton & Hove · East Sussex
Glass Splashbacks in Brighton & Hove
Want a wipe-clean wall behind a basin or vanity in Brighton & Hove? We can quote for toughened glass splashbacks in colours, satin finishes or clear glass over a feature wall.
- BN1
- BN3
- BN2
- Guide from £225
Kitchen glass splashback in Brighton & Hove
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
The price depends on the total glass area, the number of panels and joints, the number of cut-outs, the colour and glass type, and access to the wall. Low-iron glass, metallic or printed finishes and complex shapes add cost. See the guide prices for typical ranges.
What you get
- Bonding with adhesive compatible with the painted back
- Silicone-finished edges, final clean and care advice
- Back-painting to your chosen colour or finish
- Toughened glass made to template with factory cut-outs
About Brighton & Hove for this job
- Postcodes covered
- BN1, BN3, BN2 and the surrounding area, including Burgess Hill, Worthing and Seaford
- Coast
- Brighton & Hove is about 1 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Brighton & Hove the midwinter sun reaches about 16° above the horizon at noon, with roughly 7.7 hours of daylight, rising to about 63° and 16.3 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Kitchens in flats and terraces often have narrow access and tight stairs, so long splashbacks may be split into shorter panels with planned joints. Parking for the fitting team and building rules on working hours can also affect scheduling.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Brighton & Hove
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Glass Splashbacks in Brighton & Hove: questions
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How do you match the colour of a glass splashback?
We can match many paint and RAL colours, and the most reliable way to choose is from a physical glass sample viewed in your own kitchen. Colours look different on screens and under different lighting. For pale colours we usually suggest low-iron glass, because standard glass adds a green tint to the painted back.
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
Do you cover Brighton & Hove for glass splashbacks?
Yes. We can quote for glass splashbacks across Brighton & Hove and the surrounding East Sussex area, including postcode districts BN1, BN3 and BN2, and nearby Burgess Hill, Worthing and Seaford. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Brighton & Hove
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.