Droylsden · Greater Manchester
Glass Splashbacks in Droylsden
Fitting a new kitchen in Droylsden? Once the worktops and hob are in, we can template, colour-match and fit glass splashbacks that line up with your units and sockets.
- M43
- M11
- M18
- Guide from £225
About kitchen glass splashback in Droylsden
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
What you get
- Bonding with adhesive compatible with the painted back
- Survey and templating after worktops and hob are fitted
- Toughened glass made to template with factory cut-outs
- Silicone-finished edges, final clean and care advice
Droylsden at a glance
- Postcodes covered
- M43, M11, M18 and the surrounding area, including Failsworth, Denton and Ashton-under-Lyne
- Coast
- Droylsden is well inland, around 44 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Droylsden the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.2 hours of daylight, rising to about 60° and 16.8 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Droylsden
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Droylsden: questions
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Do you cover Droylsden for glass splashbacks?
Yes. We can quote for glass splashbacks across Droylsden and the surrounding Greater Manchester area, including postcode districts M43, M11 and M18, and nearby Failsworth, Denton and Ashton-under-Lyne. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Droylsden
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.