Farnworth · Greater Manchester
Glass Splashbacks in Farnworth
We cover Farnworth and Greater Manchester for glass splashbacks in kitchens, utility rooms and bathrooms, with every job templated on site and quoted in writing before the glass is made.
- BL4
- M38
- BL3
- Guide from £225
About glass splashback behind hob in Farnworth
Glass splashbacks have no grout lines to stain, so cleaning is simply a soft cloth with warm soapy water or a non-abrasive glass cleaner. Avoid scourers, abrasive creams and sharp scrapers, which can scratch the glass surface and dull the finish over time.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
What you get
- Silicone-finished edges, final clean and care advice
- Survey and templating after worktops and hob are fitted
- Back-painting to your chosen colour or finish
- Toughened glass made to template with factory cut-outs
Local details for Farnworth
- Postcodes covered
- BL4, M38, BL3 and the surrounding area, including Walkden, Bolton and Radcliffe
- Coast
- Farnworth is well inland, around 33 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Farnworth the midwinter sun reaches about 13° above the horizon at noon, with roughly 7.2 hours of daylight, rising to about 60° and 16.8 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Farnworth
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Glass Splashbacks in Farnworth: questions
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Farnworth for glass splashbacks?
Yes. We can quote for glass splashbacks across Farnworth and the surrounding Greater Manchester area, including postcode districts BL4, M38 and BL3, and nearby Walkden, Bolton and Radcliffe. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Farnworth
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.