Pontypool · Gwent
Glass Splashbacks in Pontypool
A glass splashback in Pontypool starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- NP4
- NP44
- Guide from £225
Toughened glass splashback across Pontypool
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
What you get
- Silicone-finished edges, final clean and care advice
- Toughened glass made to template with factory cut-outs
- Back-painting to your chosen colour or finish
- Bonding with adhesive compatible with the painted back
Working in Pontypool
- Postcodes covered
- NP4, NP44 and the surrounding area, including Cwmbran, Abertillery and Abercarn
- Coast
- Pontypool sits roughly 16 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Pontypool the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.6 hours of daylight, rising to about 62° and 16.4 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Wales
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Pontypool
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Glass Splashbacks in Pontypool: questions
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Can a glass splashback go behind a hob?
Yes, provided it is toughened glass and the hob maker's clearances are followed. Toughened glass copes with the heat from a hob far better than ordinary glass, and it is what we fit behind cookers. Some gas hobs need a minimum gap to the wall, so we check your hob's instructions before the glass is ordered.
How do I clean a glass splashback?
Wipe it with a soft cloth and warm soapy water, or a non-abrasive glass cleaner, then buff dry for a streak-free finish. Grease behind the hob comes off easily because there are no grout lines. Avoid scourers, abrasive creams and blades, which can scratch the glass, and do not use cleaners that could seep behind the edges.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
Do you cover Pontypool for glass splashbacks?
Yes. We can quote for glass splashbacks across Pontypool and the surrounding Gwent area, including postcode districts NP4 and NP44, and nearby Cwmbran, Abertillery and Abercarn. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Pontypool
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.