Highlands & Islands · Scotland

Glass Splashbacks in Highlands & Islands

A glass splashback in Highlands & Islands starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.

Guide from £225
9 towns covered
Postcode areas AB, HS, IV, KW, PH, ZE

Glass splashbacks in Highlands & Islands: what to know

Splashbacks are made from toughened glass because it copes with heat from a hob and with the stress around socket cut-outs far better than ordinary glass. Untoughened coloured glass is more prone to cracking behind a hob or across a cut-out, so we only fit toughened panels.

Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.

After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.

Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.

Pale green glass splashback behind a hob in a white kitchen

Towns we cover for glass splashbacks in Highlands & Islands

Choose your town for local details, nearby areas and the postcode districts we cover.

What applies in Highlands & Islands

Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.

Highlands & Islands has its own coastline, so for homes and businesses near the sea, salt air and wind-driven rain are part of the brief. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.

Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.

Guide prices

Guide prices inc VAT for typical jobs. Remote and island locations are quoted by arrangement. Your written quote fixes the price after measuring.
Typical job	Guide price inc VAT
Hob splashback, 900 × 750 mm	£225 – £285
Run behind worktop, 2400 × 600 mm	£395 – £515
Low-iron, 900 × 750 mm	£235 – £295

Choosing your glass splashbacks

Back-painted colour

Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.

Low-iron glass

Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.

Metallic or sparkle finish

Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.

Clear glass panel

Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.

Glass Splashbacks in Highlands & Islands: questions

When should my glass splashback be measured?

Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.

What affects the cost of a glass splashback?

The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.

Can you cut holes in a glass splashback for sockets?

Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.

Can I fit a glass splashback myself?

It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.

Which parts of Highlands & Islands do you cover for glass splashbacks?

We cover the whole of Highlands & Islands, including Inverness, Elgin, Fort William, Nairn and Forres, and postcode areas AB, HS, IV, KW, PH, ZE. Building rules for glass splashbacks here follow the regulations for Scotland. Enter your postcode on the quote form and we will confirm cover; then a glazier will arrange a free survey before giving you a written quote.

Other glazing services in Highlands & Islands

All glazing in Highlands & Islands · Glass Splashbacks across the UK

Get a written quote in Highlands & Islands

Free survey for new glazing, clear guide prices and one point of contact for every glazing job.

Get a guide price 0800 088 6248 WhatsApp