Elgin · Highlands & Islands
Glass Splashbacks in Elgin
Is stained grout behind your hob in Elgin hard to keep clean? We can replace tired tiles with a smooth, wipe-clean toughened glass panel in your chosen colour.
- IV30
- Guide from £225
About glass splashback behind hob in Elgin
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Standard glass has a green tint that shows through back-painted colours, especially whites, creams and pale greys. Low-iron glass contains less iron, removes most of that tint and keeps the painted colour close to the sample, so it is the usual choice for light colours.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Colours look different on screens, in daylight and under kitchen lighting, so choose from a physical glass sample rather than a website or paint chart. We can match many paint and RAL colours, and a sample panel viewed in your own kitchen avoids surprises.
What you get
- Toughened glass made to template with factory cut-outs
- Back-painting to your chosen colour or finish
- Removal and refitting of socket and switch faceplates
- Silicone-finished edges, final clean and care advice
Working in Elgin
- Postcodes covered
- IV30 and the surrounding area, including Forres, Nairn and Inverness
- Coast
- Elgin sits roughly 8 km from the nearest coastline, close enough that exposure on open or high ground is worth considering. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Elgin the midwinter sun reaches about 9° above the horizon at noon, with roughly 6.2 hours of daylight, rising to about 56° and 17.8 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Scotland
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Elgin
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
What you can choose
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Back-painted colour
Toughened glass painted on the back in a matched colour, giving a smooth, glossy finish in almost any shade to suit units or walls.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Glass Splashbacks in Elgin: questions
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Do you cover Elgin for glass splashbacks?
Yes. We can quote for glass splashbacks across Elgin and the surrounding Highlands & Islands area, including postcode districts IV30, and nearby Forres, Nairn and Inverness. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Elgin
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.