Whitby · North Yorkshire
Glass Splashbacks in Whitby
Is stained grout behind your hob in Whitby hard to keep clean? We can replace tired tiles with a smooth, wipe-clean toughened glass panel in your chosen colour.
- YO22
- Guide from £225
Whitby: coloured glass splashback
The wall behind a splashback must be flat, sound and dry so the adhesive bonds evenly. Old tiles are usually removed and the wall made good, because uneven surfaces show through the glass and can create stress points behind the panel.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
Long runs and tall walls are usually made from more than one panel, because large sheets are heavy and hard to carry through houses. Joints are planned at corners, behind the hob centre line or at natural breaks, and are finished with a thin, neat silicone line.
Hob makers set minimum clearances between the hob and nearby wall surfaces, and gas hobs in particular can have specific requirements. We check your hob's installation instructions before ordering so the glass, its cut-outs and any joints sit where the manufacturer allows.
What a typical job includes
- Silicone-finished edges, final clean and care advice
- Bonding with adhesive compatible with the painted back
- Removal and refitting of socket and switch faceplates
- Back-painting to your chosen colour or finish
About Whitby for this job
- Postcodes covered
- YO22 and the surrounding area, including Scarborough, Redcar and Middlesbrough
- Coast
- Whitby is about 2 km from the coast or a tidal estuary, so salt air and wind-driven rain are worth planning for. Splashbacks sit indoors, so the coast affects them little, but kitchens in damp coastal homes can see condensation on cold external walls. The wall needs to be dry and sound before bonding, and good extraction helps keep edges and silicone clean.
- Daylight and sun
- In Whitby the midwinter sun reaches about 12° above the horizon at noon, with roughly 7.0 hours of daylight, rising to about 59° and 17.0 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in England
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Whitby
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Specification choices
Satin finish
Acid-etched glass with a soft, low-sheen face that reduces reflections and glare, useful opposite windows or bright lighting.
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Low-iron glass
Glass with less iron, removing the green tint of standard glass so whites, creams and pale colours look true to the sample.
Glass Splashbacks in Whitby: questions
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Why does my white glass splashback look slightly green?
Standard glass contains iron, which gives it a green tint that shows through pale back-painted colours, particularly white and cream. Low-iron glass has much less iron, so the colour behind looks close to the painted sample. If you are choosing a light colour, it is worth specifying low-iron glass from the start.
What affects the cost of a glass splashback?
The main cost drivers are the total glass area, the number of panels and joints, the number of socket and switch cut-outs, the colour and glass type, and how easy the wall is to reach. Low-iron glass, metallic or printed finishes and shaped panels add cost. See the guide prices for typical ranges.
When should my glass splashback be measured?
Your splashback should be templated after the worktops, units and hob are installed and any electrical work is finished. The glass is made to the exact finished dimensions, including socket positions, so measuring from plans or before worktops go in often leads to panels that do not fit and have to be remade.
Do you cover Whitby for glass splashbacks?
Yes. We can quote for glass splashbacks across Whitby and the surrounding North Yorkshire area, including postcode districts YO22, and nearby Scarborough, Redcar and Middlesbrough. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Whitby
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.