Brecon · Powys
Glass Splashbacks in Brecon
A glass splashback in Brecon starts with templating after the worktops are fitted, then a written quote that fixes the price for the glass, colour and finish shown.
- LD3
- Guide from £225
Glass splashbacks across Brecon
Our glaziers remove and refit socket and switch faceplates so the glass can sit behind them, with the power isolated first. Moving or adding sockets, or any other electrical alteration, needs a qualified electrician, ideally before the splashback is templated.
Splashbacks are templated once the worktops, units and hob are fitted, not from kitchen plans. Worktop heights, wall angles and socket positions often move during installation, and the glass is made to the finished dimensions so edges line up and gaps stay even.
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on colour and finish. Fitting a typical kitchen takes part of a day, and the kitchen can normally be used again straight afterwards, though the silicone needs time to cure fully.
Toughened glass cannot be cut or drilled after toughening, so every socket, switch, extractor and window-reveal cut-out is made beforehand. Sockets cannot be moved after the glass is ordered without remaking the panel, so electrical positions need to be final at templating.
What you get
- Removal and refitting of socket and switch faceplates
- Silicone-finished edges, final clean and care advice
- Bonding with adhesive compatible with the painted back
- Back-painting to your chosen colour or finish
Working in Brecon
- Postcodes covered
- LD3 and the surrounding area, including Brynmawr, Tredegar and Merthyr Tydfil
- Coast
- Brecon is well inland, around 48 km from the nearest coast, so salt exposure is not usually a factor.
- Daylight and sun
- In Brecon the midwinter sun reaches about 15° above the horizon at noon, with roughly 7.5 hours of daylight, rising to about 62° and 16.5 hours in midsummer. Glossy glass reflects light from windows and under-cabinet lighting, brightening a dark kitchen. Low winter sun hitting a glass wall can cause glare, so a satin finish may suit a splashback that faces a south-facing window.
- Access and setting
- Older rural homes often have uneven solid walls with lime plaster or stone, so the wall may need making flat before glass can be bonded. Where a range cooker is fitted, its heat and clearance needs are checked before ordering.
- Rules in Wales
- Building regulations do not usually apply to this type of work, but we confirm anything that does in writing with your quote.
Guide prices in Brecon
| Typical job | Guide price inc VAT |
|---|---|
| Hob splashback, 900 × 750 mm | £225 – £285 |
| Run behind worktop, 2400 × 600 mm | £395 – £515 |
| Low-iron, 900 × 750 mm | £235 – £295 |
Options to choose between
Printed design
A digitally printed image or pattern on the back of the glass, sealed behind it so the front stays smooth and wipeable.
Clear glass panel
Unpainted toughened glass over a painted wall or feature finish, protecting it from splashes while letting the surface behind show.
Metallic or sparkle finish
Back-painted glass with metallic or fine sparkle effects, adding depth and reflection without the upkeep of polished metal.
Glass Splashbacks in Brecon: questions
Can I fit a glass splashback myself?
It is possible, but the risks are mostly in measuring and handling. A small error in templating or a socket position means the toughened panel has to be remade, because it cannot be trimmed. Large panels are heavy and awkward to place without damaging worktops, and the adhesive must suit the painted back. We measure, make and fit as one job.
Can a glass splashback be fitted over existing tiles?
It is usually better to remove the tiles and make the wall good first. Glass needs a flat, sound surface for the adhesive to bond evenly, and grout lines, uneven tiles or loose tiles can show through or create stress points. Removing tiles also stops the glass standing too far forward of the worktop and sockets.
Can you cut holes in a glass splashback for sockets?
Yes. Socket, switch and extractor cut-outs are made at the factory before the glass is toughened, because toughened glass cannot be cut afterwards. That means socket positions must be final when we template. If sockets need moving or adding, a qualified electrician should do that first, and we template around the new positions.
How long does it take to get a glass splashback fitted?
After templating, made-to-measure splashbacks are usually ready within a few weeks, depending on the colour and finish. Fitting a typical kitchen takes part of a day, and you can normally use the kitchen again once we have finished. The silicone needs time to cure fully, and we tell you how long on the day.
Do you cover Brecon for glass splashbacks?
Yes. We can quote for glass splashbacks across Brecon and the surrounding Powys area, including postcode districts LD3, and nearby Brynmawr, Tredegar and Merthyr Tydfil. Start with your postcode on the quote form and a glazier will arrange a free survey before giving you a written quote.
Get a written quote in Brecon
Free survey for new glazing, clear guide prices and one point of contact for every glazing job.